Rega P7 Turntable - Black / Dynavector 10X5 Cartridge

Rega P7 Turntable
Rega’s philosophy is to make high quality products at sensible prices, as a means of reproducing music as faithfully as possible. Rega is committed to the design and development of new and existing products, both in hi-fi and other areas, that will perpetuate Rega’s values of quality and value for money.
The Rega P7 has been designed to be effective, easy to use and above all – to reproduce music better than any other turntable. We have omitted all the usual gimmicks and genuinely concentrated the manufacturing costs on the high quality components and design necessary to reproduce records accurately.
For example: a complex sub-chassis suspension is normally necessary to reduce motor noise. However they are difficult to maintain and degrade performance. Rega have designed a unique phase adjustable power supply which eliminates motor vibration at source and therefore eradicates the need for a suspension.
Rega’s design skill and the use of extremely high quality components ensure that your turntable will perform at its optimum.
The P7 has a new tonearm, the RB700, improving greatly on the previous model, the RB600. The aluminium tube has been specially coated in a unique finish and the entire bearing housing has been redesigned and is now manufactured to even higher tolerances.
The tonearm tube itself (which is a one piece silicone/aluminium casting) is very rigid, whilst being low mass. The tonearm assembly is concentrated around precision, hardened stainless steel, miniature ball races of the highest quality. The bearings fit on to ground shafts and into the tonearm using interference fits. This means that no adhesive is required and therefore none of the associated (component – adhesive – component) losses in rigidity prevail. It is fitted to the plinth by a 3-point fixing which is CNC machined out of a single solid block of Stainless steel. This provides the strongest most rigid base structure possible for the tonearm and causes less stress on the plinth and the RB700’s bearing housing, and therefore the least possible resonance.
The RB700 tonearm is designed to make cartridges work harder, maximising the cantilever acceleration and travel as much as possible with the utmost accuracy within the cartridge body thus providing new levels of information.
The platter is produced from a ceramic oxide powder which is compressed, fired and diamond ground to size. (Because this platter is as stiff and hard as sapphire, the only improvement that can be made would me to make it from diamond.) This is a first in the industry at volume production levels.
Even so, each platter takes many hours to produce. Expensive detail design ensures it only sits on three points on the centre hub. We have also used new techniques to achieve better speed stability of the turntable by using ceramic weights to provide a flywheel effect to the platter.
The new P7 plinth is made from an even lighter material than the original Planar which again offers advantages over its predecessor. The plinth is of a skeletal design. This allows the mass to be reduced and the rigidity increased in comparison to a solid section construction. All organic materials used in the production of the plinth and surround are obtained from sustainable sources.
The motor is a high specification, P9 24V twin phase synchronous unit controlled by Rega’s unique and innovative TT PSU power supply. The motor drives the computer-numerically-controlled (CNC) machined pulley and sub platter/hub-bearing assembly via a twin belt drive. Two belts are used so that any small inaccuracies in one belt will be cancelled out by the second, giving unusually low levels of wow and flutter.
The compact TT PSU uses exactly the same high stability crystal locked low distortion sine wave generator as is used in the heart of the P9 power supply.
This, along with an efficient drive amplifier fed from a stabilised DC power supply, generates a 24V AC balanced signal of less than 0.05% distortion, which is completely un-affected by any changes in the mains/line voltage and conditions. This then drives the improved Rega anti-vibration circuit, which is situated beneath the turntable.
The speed change is achieved by changing the frequency of the drive voltage; this is because the speed of the platter and motor is directly proportional to the motor drive frequency. A relay switches in the required phase compensation & anti vibration circuit to eradicate motor vibration to a minimum at both speeds.
We have used the highest quality purpose designed high current power and phono connectors and low noise, wide bandwidth interconnect cable. These are genuine professional products and are the best available for the job. Do not attempt to fit any other wires or cables.

Dynavector 10X5 Cartridge
The Dynavector 10X series High Output Moving Coil cartridge debuted in 1978 winning the prestigious Design and Engineering Award at the Chicago CES in both 1978 and 1981. The 10X series cartridges are also widely accepted at the benchmark in High Output moving coil cartridge at this price point and beyond.
With the introduction of the new 10X5 High Output moving coil there is no doubt Dynavector will retain this enviable position and again set the standard for high output moving coil cartridges.

Rega P7 Turntable
Drive method: belt drive
Motor: 24V AC synchronous
Platter: Ceramic
Speeds: 33.3 and 45 rpm

Dynavector 10X5 Cartridge
Type: High output moving coil cartridge with flux damper and softened magnetism
Output Voltage: 2.5 mV (at 1 kHz, 5 cm/sec.)
Channel Separation: 25 dB (at 1 kHz)
Channel Balance: 1.0 dB (at 1 kHz)
Frequency Response: 20 - 20,000 Hz (± 1 dB)
Compliance: 12 mm/dyn
Tracking Force: 1.8 - 2.2 g
Impedance: 150 ohms
Recommended Load Impedance: > 1 kOhms
Cantilever: 6 mm length aluminium pipe
Stylus Tip: Elliptical
Weight: 7.3 g

Turnaround

Orders will usually dispatched within 2 working days of receiving cleared payment.

Shipping Rates

We calculate your shipping rate based on the total weight of your items and your delivery address. Standard shipping to the UK Mainland (excludes Northern Ireland, Isle of Man, Channel Islands) is free, except where specifically indicated. Don't worry, you'll always see the final shipping charge displayed before you reach the payment step (on the checkout page).

Carriers

We despatch the bulk of our UK mainland items on a 24 hour service.  Non-Mainland locations – Isle of Man, Isle of Wight, the Scilly Isles, the Scottish highlands and Islands, the Channel Islands and Northern Ireland may take a day or so longer. Smaller items are delivered using Royal Mail 24 or special delivery. Larger items are delivered using a courier service such as UPS and occasionally by a Pallet service.

Order Tracking

If a tracking # is provided by the carrier, we will update your order with the tracking information. Please note that some orders will not have tracking numbers.